Model Y Series: Episode 13: Comparing Model 3 eAC to Model Y Heat Pump
Welcome back to episode 13 of Munro’s Tesla Model Y Performance teardown, where, Munro & Associates CEO Sandy Munro compares the Model 3 eAC compressor and NVH provisions to the isolated heat pump on the Model Y.
Model Y Series: Episode 12: Floorpan, EPP Floor Risers, Commonality through Stanchions and Wiring Observations
This is episode 12 of Munro’s Tesla Model Y Performance teardown, where Munro & Associates CEO Sandy Munro shares observations on the geometry of the floorpan, strategies for raising the floor height, enablers for re-use of Model 3 components and initial thoughts on some of the high and low voltage wiring.
Model Y Series: Episode 11: Teardown Progresses and Sandy Munro Gets into the Finer Details
Episode 11: Teardown Progresses and Sandy Munro Gets into the Finer Details Welcome back to episode 11 of Munro’s Tesla Model Y Performance teardown, where, Munro & Associates CEO Sandy Munro starts to get into the finer details of the car as the teardown progresses. In this episode, Sandy covers a number of details, including […]
Model Y Series: Episode 10: Potential 3rd Row Seating, Ingress/Egress, Rear Door Service Latch
Episode 10: Potential 3rd Row Seating, Ingress/Egress, Rear Door Service Latch Welcome back to episode 10 of Munro’s Tesla Model Y Performance teardown. In this episode, Munro & Associates CEO Sandy Munro looks at the possibility of third row seating, emergency exits and the rear door service latch. Starting by looking at the possibility of […]
Model Y Series: Episode 9 – Aeroshields MY-M3, Hood Alignment, Engine Bay Rail Reinforcements
Episode 9 – Aeroshields MY-M3, Hood Alignment, Engine Bay Rail Reinforcements Welcome back to episode nine of Munro’s Tesla Model Y Performance teardown, where Munro & Associates CEO Sandy Munro compares the aeroshields between the Model Y and Model 3, offers commentary on hood alignment and more detail on engine bay rail reinforcements catered toward […]
Model Y Series: Episode 8 – Q&A from Comments and View of Things to Come
Episode 8 – Q&A from Comments and View of Things to Come Welcome back to episode eight of Munro’s Tesla Model Y Performance teardown, where Munro & Associates CEO Sandy Munro addresses a handful of viewer questions and gives a glimpse of what to expect next. During the five-minute video, Sandy discusses four common viewer […]
Model Y Series: Episode 7 – Front Impact Structure, Snap-Fit Lamp & Rotor Serviceability
Episode 7 – Front Impact Structure, Snap-Fit Lamp & Rotor Serviceability Welcome back to episode seven of Munro’s Tesla Model Y Performance teardown, where Munro & Associates CEO Sandy Munro takes a look at the front wheel envelope and shares an overview of the: Front impact structure: looking under the wheel well at the front […]
Model Y Series: Episode 6 – Wiring, Brakes, Quick-connects & Rear Body Structure Overview
Episode 6: Wiring, Brakes, Quick-connects & Rear Body Structure Overview Welcome back to episode six of Munro’s Tesla Model Y Performance teardown, where Munro & Associates CEO Sandy Munro provides an overview of the vehicle’s wiring, coolant lines, brakes and rear body structure. From the corrugated wrap over the local 12 volt wires and the […]
Model Y Series: Episode 5 – Suspension Overview
Episode 5: Suspension Overview Welcome back to episode five of Munro’s Tesla Model Y Performance teardown, where Munro & Associates CEO Sandy Munro provides an overview of the vehicle’s suspension configuration. Sandy’s initial overview is that the Tesla Model Y and Model 3 have similar suspension systems, but it’s obvious they’re not the same. Sandy […]
Model Y Series: Episode 4 – Cowl Cover Clip
This is episode four of Munro’s Tesla Model Y Performance teardown, where Munro & Associates CEO Sandy Munro discusses a potential redesign of the Tesla Model Y cowl cover clips and gives a heartfelt message about “paying it forward” amidst the COVID-19 pandemic.